Acoustic guitar miking techniques research

Mics choosing: Condenser mics are often chosen over dynamic mics since acoustic guitars do not produce loud sounds and they have a mid to high frequency range, while a dynamic mic can be used if one wishes to get a more percussive and less musical sound.

Large or small diaphragm condenser mics: Large diaphragm condensers give a more colored sound to the acoustic guitars, while small diaphragm condensers tends to give a more natural sound.

There are a few miking techniques that can be used as references:
1. Single large diaphragm condenser mic
- Facing the area between the soundhole and the top of the fretboard, in cardiod pattern.

2. XY position
-  Two small diaphragm microphones placed at 90ยบ angle with the capsules as close to one another as possible without touching
- angle is pointed towards the sound source.

3. Spaced pair
- Used two small diaphragm mics, one is pointed towards the 8th fret, while the other at the 12th fret where the strumming happens.

4. Using Direct input
- Normally used when mics are not available.

Comments

Post a Comment

Popular posts from this blog

Electric guitar miking techniques result

Image
For the electric guitar miking techniques experiments, we are using both Rode NT1A condenser mic and a Shure SM57 dynamic mic and placed them in different position to get the right sound for a rock song. The result: 1. The SM57 is place on axis and near to the cone of the amplifier, and the NT1A is placed on the edge of the cone of the amplifier. The sound captured is punchy with attacks and the recording is quite clear with the distortions from the amplifier. 2. The SM57 is tilted a little to the left so that it is slightly off axis with the cone, and the NT1A stays at the same position. I feel like this technique gives a higher frequency and more tonality is heard from the recording. 3. The SM57 is tilted more to the left so that it is completely off axis with the cone, and the NT1A stays at the same position. This technique makes the recording muddier and also the sound is softer.
Read more

Assessment 1 conclusion

Drums: For drum miking, I would use the Glyn Johns Method as a starter for set up as it only requires 4 mics, and then add or change the mics depending on the song choices that I am recording, and also the time that I have for setting up. This method gives a nice balanced sound on the drum set, and additional spot mics can be added to each drum kit for more flexibility for the mixing process. Mic choices: Overheads: AKG C414 with cardioid patterns Kick drum: AKG P2 Snare: SM57 Toms: Sennheiser MD421 Hi-Hat: AKG C451 Acoustic Guitar: For acoustic guitar, I would choose to use a pair of AKG C414 at cardioid pattern and position it on axis on the 8th fret and 12th fret respectively. This capture much clarity from the acoustic guitar and also has a warmer low end. In the case of only 1 mic can be used, an AKG C414 will be placed on axis with the sound hole, and around 1 foot away from it. Electric guitar: I would prefer to use a SM57, place it near the cone of the amp and ...
Read more

Bass miking techniques result

Image
For the bass miking techniques experiments, we connect the bass guitar to the board via DI box and also miked it using 2 different mics in different positions which are the AKG C414 and AKG D2. The result: 1. AKG C414(On axis) with DI - The large diaphragm condenser is set to cardioid pattern is placed near to the cone of the Hartke HD150 bass amplifier. The sound is a bit muddy and is too boomy when low notes are played. 2. AKG D2(On axis) with DI The sound captured is much clearer and also with enough attacks. 3. AKG D2 (at the edge of the cone) with DI The sound is not as clear as when is positioned on axis and the low end is not as intense as well. 4. AKG D2 (off axis) with DI  The mic is tilted so that it is off axis with the cone of the amplifier. Less attack are being captured using this techniques and it is also very soft and muddy. Thus to get a clear bass definition from the playing, I prefer using the AKG D2 positioned on axis o...
Read more